WikiPhone:Phone Access:Dial in via SIP: Difference between revisions

Line 84:

== Configuring a trunk in CUCM ==

You can configure WikiPhone as a trunk in CUCM so that you can reach a WikiPhone service by dialing a DN on your phones. Since WikiPhone does not require authentication or registration, this can be done without an external border element.

You can configure WikiPhone as a trunk in CUCM so that you can reach a WikiPhone service by dialing a DN on your phones. Since WikiPhone does not require authentication or registration, this can be done without an external border element as long as your CUCM server has access to the internet.

To configure WikiPhone as a trunk, go to Device -> Trunk and choose SIP as the trunk type. Name the trunk WikiPhone. Set your device pool, and set the SIP Trunk Security Profile as "Non Secure SIP Trunk Profile". And set the SIP profile to "Standard SIP Profile". Set the Destination Address to "telephones.wiki" or if you don't have DNS, you can use our static IPv4 which is "135.148.32.154". And then save the trunk and click reset.

Now you can go to Call Routing > Route/Hunt > Route Pattern and create a new pattern. Set the call pattern to what you want for the ~~perticler~~ service. And set Gateway/Route List to your WikiPhone trunk. Then under Called Party Transformations, enter the numeric ~~number~~ of the service you want this DN to route to (not the full URI). And click save. Repeat this step for every service you wanna be able to access.

Now you can go to Call Routing > Route/Hunt > Route Pattern and create a new pattern. Set the call pattern to what you want for the particular service. And set Gateway/Route List to your WikiPhone trunk. Then, under Called Party Transformations, enter the numeric URI of the service you want this DN to route to (not the full URI). And click save. Repeat this step for every service you wanna be able to access.

Once you are done, you should now be able to dial the DN you configured to reach the particular service of your choice. If you cannot hear audio, make sure your codecs are setup correctly, and that calls are being routed properly over NAT. If your call is declined, ensure you used a vaild number, and that the IP/FQDN is correct.

@@ Line 84: / Line 84: @@
 == Configuring a trunk in CUCM ==
-You can configure WikiPhone as a trunk in CUCM so that you can reach a WikiPhone service by dialing a DN on your phones. Since WikiPhone does not require authentication or registration, this can be done without an external border element.
+You can configure WikiPhone as a trunk in CUCM so that you can reach a WikiPhone service by dialing a DN on your phones. Since WikiPhone does not require authentication or registration, this can be done without an external border element as long as your CUCM server has access to the internet.
 To configure WikiPhone as a trunk, go to Device -> Trunk and choose SIP as the trunk type. Name the trunk WikiPhone. Set your device pool, and set the SIP Trunk Security Profile as "Non Secure SIP Trunk Profile". And set the SIP profile to "Standard SIP Profile". Set the Destination Address to "telephones.wiki" or if you don't have DNS, you can use our static IPv4 which is "135.148.32.154". And then save the trunk and click reset.
-Now you can go to Call Routing > Route/Hunt > Route Pattern and create a new pattern. Set the call pattern to what you want for the perticler service. And set Gateway/Route List to your WikiPhone trunk. Then under Called Party Transformations, enter the numeric number of the service you want this DN to route to (not the full URI). And click save. Repeat this step for every service you wanna be able to access.
+Now you can go to Call Routing > Route/Hunt > Route Pattern and create a new pattern. Set the call pattern to what you want for the particular service. And set Gateway/Route List to your WikiPhone trunk. Then, under Called Party Transformations, enter the numeric URI of the service you want this DN to route to (not the full URI). And click save. Repeat this step for every service you wanna be able to access.
 Once you are done, you should now be able to dial the DN you configured to reach the particular service of your choice. If you cannot hear audio, make sure your codecs are setup correctly, and that calls are being routed properly over NAT. If your call is declined, ensure you used a vaild number, and that the IP/FQDN is correct.